0

Your Cart is Empty

Kaabo Wolf Warrior 11+ Help

Need Help With Your Kaabo Wolf Warrior 11+?

You've come to the right place! Here are FAQs and a ton of tutorials for maintaining your Wolf Warrior 11+ long-term. You'll also find scooter upgrade tutorials for replacing the handlebars, swapping throttles, and more.

  1. If you're troubleshooting issues with your Kaabo Wolf Warrior 11+, here are some things to try:
    The first step would be to identify if you are able to turn on the key electrical components of the scooter (LCD display, voltmeter power on, throttle responds).
  2. Next, would be to test if the scooter is able to move at all. Check your P-settings to ensure that the "kickstart" feature is turned off.
  3. If experiencing an issue, identify which part is causing the issue. (Stem, Handlebars, LCD Display, Battery, etc.)
  4. Find answers to your questions below with your Kaabo Wolf Warrior 11+ video tutorials and FAQs.

If you are unsure about the issue or cannot find a suitable guide, reach out to our 24/7 live chat for assistance.

Setup & Maintenance Guides

Click on each tab to expand & view each tutorial

[Setup] Kaabo Wolf Warrior 11+ User Manual

Here's the user manual for the Kaabo Wolf Warrior 11 electric scooter.

[Setup] How to fold and unfold the Wolf Warrior 11+ electric scooter

Quick Notes

How to fold:

Step 1: Remove the protection pin
Step 2: Rotate the center piece to "unlock" the position. This will allow the large mechanism to move freely.
Step 3: Once the mechanism is loose, lift the bolt up and the stem should fold down smoothly

To unfold:

Step 1: Push the stem forward into its locking position and fold the bolt down.
Step 2: Fold the flush metal down to lock the position.
Step 3: Place the protection pin back in.

[Display] How to use the EY3 display and adjust P-settings

Quick Notes

Turn on display by holding down the power button
Cycle through general display functions by pressing -Mode
Press the speed step (dot) button to customize the setting
Long press mode to access P-settings

P0 - Wheel diameter (Do not change)

  • Mantis - set to 10
  • WW and WK- set to 11

P1- System voltage (Do not change)
P2- number of motor poles (Do not change)
P3- Speed signal selection (Do not change)
P4- Unit of measurement (1 - miles, 0 - Kilometres)
P5- Kick or throttle start (1 - kick , 0 - throttle)
P6- Cruise control (0 - Off, 1 - On)

  • You can use it usually for long trips.
  • If you hold the throttle for 5 seconds, releasing it will keep the current speed.
  • To stop the Cruise control, tap the throttle lightly or use the brakes

P7 - Acceleration of the scooter (0 - Highest , 5 - Slowest)
P8 - Maximum voltage output (Display by percentage)
P9 - Energy saving mode (1 - Max energy saving, 3 - No energy saving)

PA - Electric braking strength (0 - Off, 1 - Little, 5 - Strong)
PB - Display brightness (0 - No background light, 5 - Brightest)
PC - Auto turn off time in mins (Can customize between 1-30 mins)
PD - ABS braking (0 - Off, 1 - On)

Error Messages:

  • Exclamation mark - Seen when you hit the brakes. But if the error code appears without hitting the brakes, that means you have a faulty brake.
  • Throttle error - This means throttle issue.
  • Letter M error - This means a motor issue has occurred.

Buttons:

Eco Turbo - Help save battery and use for longer rides. Reduces top speed and motor performance.
Single Dual- Will determine if both motors are active. Tapping the button will cycle between these two options.

[Brakes] How to change the brake pads on the Wolf Warrior 11+

Quick Notes

Step 1: Locate the pin holding the pads in place.

Step 2: Using pliers, unbend the right angle made at the end of the pin

Step 3: Pull the pin once it is straightened and lift the old pads.

Step 4: Slide the old pads out of the metal casing and replace it with the new ones

Step 5: Place the metal casing back to the brake unit.

Step 6:  Place the pin back and bend it.

[Brakes] How to replace the brake caliper and brake line

Quick Notes

How to replace the rear caliper for Mantis PRO SE:

Step 1: Unscrew the rear caliper from its base.
Step 2: On the left lever, grip the plastic cap with pliers.or your fingers and pull it back so we can see the screw.
Step 3: Loosen the screw on the lever and pull the line out.
Step 4: Cut the zip ties that keep the cable in place.
Step 5: Remove the 2 screws from the front cover, pull out the cover and let it hang.
Step 6: Find the line organizer piece located at the opening beneath the stem and unscrew it.
Step 7: Unscrew the 3 screws on the back cover, gently pull it out and let it hang there.
Step 8: Slightly lift the mat along the edges to remove the two strips of tape covering it.
Step 9: Unscrew the 10 screws holding the plate (deck cover) down.
Step 10: Remove the cover and lift the battery up.
Step 11: Cut the old line below the stem and pull the line out

Important note: Make sure that you allow the oil to drip completely before pulling the line out.

Step 12: Take your new brake caliper and attach it to the base.
Step 13: Wire the line through the cavity along the edge of the scooter and into the battery cavity.
Step 14: Guide the line through the slot at the front right of the cavity. Push the line upwards and out of the slot.
Step 15: Push the line up the stem. Once you can see the tip of the line through the hole, begin pushing it towards you.
Step 16: Grab the tip of the line and pull it through completely.
Step 17: Take the plastic cover and lever screw from earlier and slide them on to the new line.
Step 18: Get the small gold piece from the caliper kit and slide it into the line.
Step 19: Remove the small gold cap at the end of the line and insert the new line to the lever.
Step 20: Secure the line by tightening the screw and slide the plastic cover.
Step 21: Fill up the brake line with brake fluid until full.
Step 22: Find a way to hold the lever into a de-press position. Head down to the caliper and tighten the screws to the base. Once done, unbind the lever.
Step 23: Put the front plastic cover back on and guide it back to the scooter carefully.
Step 24: Once the screw holes line at the bottom, secure it with the screws. Secure the line organizer and put the rear plastic cover back.
Step 25: Place the battery back to the cavity and put the metal cover back on. Once done, put all the 10 screws back.

How to replace the front caliper:

Step 1: Unscrew the rear caliper from its base.
Step 2: On the right lever, grip the plastic cap with pliers.or your fingers and pull it back so we can see the screw.
Step 3: Loosen the screw on the lever and pull the line out.
Step 4: Find the zip ties holding the line of the front caliper and cut them.
Step 5: Cut the brake line right above the caliper and let the brake fluid drain out onto a paper towel. Once completely drained, pull the line out from the top.
Step 6: Screw the new caliper to the front base and leave it slightly loose.
Step 7: Start threading the line up the stem and push the tip of the line once you see it through the hole.
Step 8: Attach the plastic cover, then the screw and finally the small gold piece.
Step 9: Remove the gold cap at the end of the line, and stick the line in the slot.
Step 10:  Secure the line by tightening the screw and slide the plastic cover.
Step 11: Fill up the brake line with brake fluid until full.
Step 12: Find a way to hold the lever into a de-press position. Head down to the caliper and tighten the screws to the base. Once done, unbind the lever.

How to change the calipers for the WW:

Step 1: Unscrew the rear caliper from its base.
Step 2: On the left lever, grip the plastic cap with pliers.or your fingers and pull it back so we can see the screw.
Step 3: Loosen the screw on the lever and pull the line out.
Step 4: Undo the velcro straps keeping the line covers in place along the stem and remove the line cover as well.
Step 5: Slightly lift up the deck pad and unscrew the seven screws holding the deck.Once done, lift up the board and the plastic liner beneath it and put it aside.
Step 6: Unscrew the fender and the 3 screws holding the front cover in place
Step 7: Cut the brake line. Make sure to drain the brake fluid completely before pulling the line out.
Step 8: Attach the new caliper to the rear base.
Step 9: Push the line through the body cavity. Guide the line through the cavity and through the opening of the front cavity.One through, guide it to the top lever.
Step 10: Slide the plastic cover, the screw and the and the small gold piece from the new caliper set on the brake line.
Step 11:Remove the gold cap at the end of the line and stick the line in the lever slot. Tighten the screw and slide the plastic cover over
Step 12: Refill the brake fluid. Once full, hold the lever to a de-press position and tighten the calipers to its base.Unbind the lever once done.
Step 13: Place the deck cover back and secure it with the screws.
Step 14: Screw the front cover back. Once done, make sure to install the fender.
Step 15: Put the cord liner back along the cords and velcro it in place.

How to replace front caliper for WW

Step 1: Unscrew the front caliper from its base.
Step 2: On the right lever, grip the plastic cap with pliers.or your fingers and pull it back so we can see the screw.
Step 3: Loosen the screw on the lever and pull the line out.
Step 4: Undo the velcro straps keeping the line covers in place along the stem and remove the line cover as well.Remove the old line and caliper completely
Step 5: Screw the new caliper to the front base.
Step 6: Start threading the line up the stem. of the front cavity.Slide the plastic cover, the screw and the and the small gold piece from the new caliper set on the brake line.
Step 7: Remove the gold cap at the end of the line and stick the line in the lever slot. Tighten the screw and slide the plastic cover over
Step 8: Refill the brake fluid. Once full, hold the lever to a de-press position and tighten the calipers to its base.Unbind the lever once done.
Step 9: Put the cord liner back along the cords and velcro it in place.

[Brakes] How to refill brake fluid in hydraulic brakes

Quick Notes

Step 1: Remove the screw on the brake lever. Position the lever where the screw is facing the ceiling.

Step 2: Once the screw and washer is removed, screw in the hose attachment.

Step 3: Slide the syringe into the hose

Step 4: If the connection is secured already, pour the hydraulic oil and insert the plunger to start pushing the fluid into the lever.

Step 5: Start pumping the brake lever continuously. Make sure that there are no longer bubbles coming out of the hose before you stop pumping the lever.

Step 6: Finally, place the original screw and washer back to the lever.

[Accessories] How to install a seat on the Wolf Warrior 11

[Accessories] How to install a steering damper on the Wolf Warrior 11

[Tires] How to fix a flat tire

How to Get Support From Us (The Fastest Way)

  1. Take a video showcasing the key issue faced
  2. Send it to support@voromotors.com
  3. Our technical team will be evaluating and assisting you with your issue faced within 24-48 hours

In your email and video, try to be as descriptive as possible to prevent unnecessary back and forth communication and to help our team be more precise when diagnosing the issue for you.

For example, if you are hearing a weird sound coming out of the tires, the video should consist of the "sound" that is being experienced. In your email, you should also include your order ID (Eg. #VORO1111) and modelso that we can acquire details of your order as quickly as possible.

Our technical team normally responds within 24-48 hours, excluding weekends. We do try our best to assist you in every way possible and seek your kind understanding on this.

Can't Find What You're Looking For?

Still not sure what you're looking for or where to go? No problem! We can guide you through it with one of our many customer support options. We're here for you pre-purchase, post-purchase, and for the long run!