The Inmotion RS 3.0 arrives in two packages: the scooter, and one accessory box. Four parts go on at home: the handlebar, the headlight, the steering damper and the rear fender. We filmed the whole setup, and this guide walks through it with every screw accounted for.
Prefer YouTube? Watch it on our channel.
What is in the accessory box
- Tools
- Charging cable
- Reflectors
- User manual
- Screw pack
- Charger
- Rear fender
- Front headlight
- Steering damper
The screw pack: twelve screws, four jobs
Sort the screws before you start so none go missing. Each size has one job.
Step 1: Fit the handlebar
- Position the wires properly first, and push them all to the front.
- Put on the clamp. Set the TFT display to roughly the angle you want.
- Start the two screws at the front, then the two at the bottom. Get them in a bit first, using the tool that comes in the box.
- Align the handlebar where you like it. Lock the front two screws first, tighten them a little, then clamp down the back.
- Always go back to the front and tighten again. Make sure everything is tight.
- Move the TFT to the angle you like, then tighten it.
If you need to readjust anything on the handlebar later, just use the tool kit.
Step 2: Install the headlight
- Mount the headlight with the big half rounded hex screw.
- Take the cap off the connector, then plug the headlight in.
- Position the wires neatly.
Step 3: Install the steering damper
- Put the damper in place with the two bigger hex screws.
- Do not tighten the first screw right away. Get all the screws in, then tighten them.
New to steering dampers? Our guide explains what a damper does, which way to turn the knob, and how to set it.
Step 4: Fit the rear fender
Fit the rear fender with the four small hex screws and the half rounded hex screw. That is the last part, and your RS 3.0 is set up.
Inmotion RS 3.0: price and availability
- RS 3.0, Midnight or Yellow: $3,499. Preorders are open and shipping starts in November. See the RS 3.0
- RS Midnight Lite: $2,599, in stock in Los Angeles. See the Midnight Lite
For everything that changed on the 3.0, read Inmotion RS 3.0 Unboxed: Every Upgrade, and a Touchscreen You Can Try, and for the full specification see Inmotion RS 3.0: What Is in the Latest Full Power RS.
Frequently asked questions
What comes in the Inmotion RS 3.0 box?
The RS 3.0 ships in two packages: the scooter and one accessory box. The accessory box holds tools, the charging cable, reflectors, the user manual, a screw pack, the charger, the rear fender, the front headlight and the steering damper.
Which screws go where on the RS 3.0?
Four long hex screws for the handlebar, one big half rounded hex screw for the headlight, two bigger hex screws for the steering damper, and four small hex screws plus one half rounded hex screw for the rear fender.
What order should I assemble the RS 3.0 in?
Handlebar first, then the headlight, then the steering damper, then the rear fender.
How do I tighten the RS 3.0 handlebar clamp?
Start all four screws loosely, lock the front two first and tighten them a little, clamp down the back, then go back to the front and tighten again so everything is tight.
Should I tighten the damper screws one at a time?
No. Put both damper screws in first, then tighten them.
Is the RS 3.0 shipping now?
The RS 3.0 is on preorder at $3,499 in Midnight or Yellow, and shipping starts in November. The RS Midnight Lite is in stock in Los Angeles at $2,599.
Stuck on a step? Contact us and tell us where you are in the setup.
